C-MAX Time Solutions
4.
Pinning
Data Sheet
CMMR-8P
Symbol
ANT2
IN2
IN1
ANT1
VCC
QHOUT
QMOUT
QLOUT
GND
QIN
DEM
PK
TEST
PON
HLD
GNDL
BSI1
BSI2
DT
DATA
DR
CLOCK
SS1
SS2
VL
CLKSEL
Function
Antenna switch 2
Input antenna
Input antenna
Antenna switch 1
Analog part supply voltage
Crystal 3 output
Crystal 2 output
Crystal 1 output
Analog Ground
Crystal common input
Capacity for demodulation
peak-detector
Capacity for AGC regulation
Test I/O
Power on
AGC Hold
Digital Ground
Bit Strength Indicator 1 (LSB)
Bit Strength Indicator 2
(MSB)
Data Send Clock
Data Output
Data Ready in register
Clock input 1024 / 4096 Hz
Transmitter Select 1
Transmitter Select 2
Digital supply voltage
Clock select
Remark
Antenna connection for 60kHz. Capacitor space CM for
capacitor to match connection between ANT2 and IN1 for
60kHz.
Antenna connection for 40kHz and 77.5kHz. Capacitor
space CH for capacitor to match connection between IN1
and IN2 for 77.5kHz
Antenna connection for 60kHz and 77.5kHz
Antenna connection for 40kHz. Capacitor space CL for
capacitor to match connection between ANT1 and IN2 for
40kHz.
Separate power supply to analog part
Connection for 77.5kHz crystal
Connection for 60kHz crystal
Connection for 40kHz crystal
separate GND to analog part
Common crystal input connection for all crystals
Capacitor C3 fixed as 100nF for all frequencies at DEM
pin
Capacitor C4 fixed as 3.3 μF for all frequencies at PK pin
Test mode set by setting SS1 and SS2
Connect to GND for receiver to be activated
Active Low hold pin to hold AGC function
Separate GND for digital part
Binary output to show LSB of BSI level
Binary output to show MSB of BSI level
Refer to timing diagram in CME8000 datasheet
Refer to timing diagram in CME8000 datasheet
Refer to timing diagram in CME8000 datasheet
Clock input necessary to drive CME8000, selectable via
CLKSEL
Different protocols and test modes selectable by this tri-
state pin (refer to logical function table for SS1 and SS2 in
CME8000 datasheet)
Different protocols and test modes selectable by this tri-
state pin (refer to logical function table for SS1 and SS2 in
CME8000 datasheet)
Separate power supply to digital part
Open/GND connection = 1024 Hz, VCC = 4096 Hz
SPEC No.
CMMR-8P
Revision
A2
State
09.01.08
C-MAX printed
10.01.2008
Version
English
Page
3 of 6
相关PDF资料
CMPA0060002F-TB BOARD DEMO AMP CIRC CMPA0060002
CMS01G LED GRN RECT MODULAR VERT MNT
CMW01Z LED T1 MODULE YELLOW TELLOW DIFF
CN10953_IRIS-M LENS IRIS MEDIUM 30DEG MCE
CN11470_IRIS-O LENS/HLDR/SUB LENS
CNW1-7219 LAMP INCAND 3MM NEO WEDGE 12V
CNW1-7220/GRABASE LAMP INCAND 3MM NEO WEDGE 18V
CP10317_LEDILSTAR-P-SUB LENS LEDILSTAR OSTAR PROJ 14DEG
相关代理商/技术参数
CMMS22G5-34SL2L 制造商:Vishay Dale 功能描述:- Bulk
CMMS22G5-5SK2035-M101 制造商:Vishay Dale 功能描述:- Bulk
CMMSH1-100 制造商:CENTRAL 制造商全称:Central Semiconductor Corp 功能描述:SURFACE MOUNT SILICON SCHOTTKY RECTIFIERS SCHOTTKY RECTIFIERS
CMMSH1-100G 制造商:CENTRAL 制造商全称:Central Semiconductor Corp 功能描述:SURFACE MOUNT SILICON SCHOTTKY RECTIFIER 1 AMP, 20 THRU 100 VOLTS
CMMSH1-100G TR 制造商:Central Semiconductor Corp 功能描述:Diode Schottky 100V 1A 2-Pin SOD-123F T/R
CMMSH1-20 制造商:CENTRAL 制造商全称:Central Semiconductor Corp 功能描述:SURFACE MOUNT SILICON SCHOTTKY RECTIFIER 1 AMP, 20 THRU 100 VOLTS
CMMSH1-20 LEADFREE 功能描述:肖特基二极管与整流器 SCHOTTKY RECTIFIER RoHS:否 制造商:Skyworks Solutions, Inc. 产品:Schottky Diodes 峰值反向电压:2 V 正向连续电流:50 mA 最大浪涌电流: 配置:Crossover Quad 恢复时间: 正向电压下降:370 mV 最大反向漏泄电流: 最大功率耗散:75 mW 工作温度范围:- 65 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-143 封装:Reel
CMMSH1-20_10 制造商:CENTRAL 制造商全称:Central Semiconductor Corp 功能描述:SURFACE MOUNT SILICON SCHOTTKY RECTIFIER 1 AMP, 20 THRU 100 VOLTS